{"id":7466247094491,"title":"Tempco Hi-Density Immersion Cartridge Heaters","handle":"tempco-immersion-cartridge-heaters","description":"\u003cp data-mce-fragment=\"1\"\u003eTempco immersion cartridge heaters \u003cspan data-mce-fragment=\"1\"\u003eare designed for heating water and other liquids. The high watt density capabilities of this heater permit greater heat dissipation in given area than would tubular immersion heaters.  However, it is important to note that allowable watt density depends on the material being heated.  For water heating, watt densities of several hundred watts per square inch are possible; oil heating may be limited to 5 to 20 watts per square inch.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSpecifications:\u003c\/strong\u003e\u003c\/h3\u003e\n\u003ch4\u003e\u003cem\u003eDesign Features\u003c\/em\u003e\u003c\/h4\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cem\u003ePassivated Incoloy Sheath\u003c\/em\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cem\u003e10\" long Teflon® Insulated lead wires\u003c\/em\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cem\u003eBrass Fitting\u003c\/em\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cem\u003eEpoxy Seal at Lead End, 266°F (130°C) Standard, 194°F (90°C) UL Rating\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cem\u003eTermination Location\u003c\/em\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003ch4\u003eSingle-Ended Straight Termination\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003e \u003cimg src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC091.jpg?Small\" alt=\"\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC091.jpg\" width=\"223\" height=\"164\" style=\"display: block; margin-left: auto; margin-right: auto;\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC091.jpg?Small\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eThe Electrical Termination is located at one end of the heater and exits straight out from the heater.\u003c\/em\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003c\/h3\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003eElectrical Terminations\u003c\/em\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003eType F: Internally Connected Flexible Leads\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cimg height=\"164\" width=\"223\" alt=\"\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC002.jpg\" src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC002.jpg?Small\" style=\"display: block; margin-left: auto; margin-right: auto;\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC002.jpg?Small\"\u003e \u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003e\u003cem\u003eThe fiberglass lead wires are internally connected to the terminal pins. This lead termination provides flexibility, permitting the lead wires to be sharply bent as they exit the heater.\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eMinimum 3\/8\" up to 1\" unheated section at the lead end is required.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eStandard lead wire temperature rating for HDC \u0026amp; HDM: 842°F (450°C).\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eStandard lead wire temperature rating for LDC: 482°F (250°C).\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eStandard 10\" (254 mm) leads. Specify longer leads.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eFor HDC \u0026amp; HDM heaters, leads longer than 60\" require a splice.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-23 for Standard and Custom Features, as well as Ordering Information.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTo reference Standard (Stock \u0026amp; Non-Stock) Order Listings - Select \u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_US_Measures.pdf?v=1640092972\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List - US Measures and Values\" style=\"color: #ff2a00;\"\u003eUS Measures\u003c\/a\u003e\u003c\/span\u003e or\u003cspan\u003e \u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_Metric_Measures.pdf?v=1640092972%20\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List- Metric Measures \u0026amp; Values\" style=\"color: #ff2a00;\"\u003eMetric Measures\u003c\/a\u003e\u003c\/span\u003e.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/em\u003e\u003c\/h3\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTermination Options\u003c\/strong\u003e\u003c\/em\u003e\u003c\/h3\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003eType TL: Teflon® Leads\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eMaximum temperature rating: 200°C (392°F)\u003c\/em\u003e\u003cem\u003e \u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-23 for Standard and Custom Features, as well as Ordering Information.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTo reference Standard (Stock \u0026amp; Non-Stock) Order Listings - Select \u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_US_Measures.pdf?v=1640092972\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List - US Measures and Values\" style=\"color: #ff2a00;\"\u003eUS Measures\u003c\/a\u003e\u003c\/span\u003e or\u003cspan\u003e \u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_Metric_Measures.pdf?v=1640092972%20\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List- Metric Measures \u0026amp; Values\" style=\"color: #ff2a00;\"\u003eMetric Measures\u003c\/a\u003e\u003c\/span\u003e.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/em\u003e\u003c\/h3\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSheath Options\u003c\/strong\u003e\u003c\/em\u003e\u003c\/h3\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003eType CM: Single Threaded Fitting\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e        \u003cimg height=\"146\" width=\"253\" alt=\"Type CM Fig. 1 - Fitting Flush with Lead End of Sheath\" src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/C030_CMA_Fig1_Dim.jpg?Medium\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/C030_CMA_Fig1_Dim.jpg?Medium\"\u003e\n\u003c\/td\u003e\n\u003ctd\u003e\u003cimg height=\"146\" width=\"252\" src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/C030b_CMV_Fig2_Dim.jpg?Medium\" alt=\"Type CM Fig. 2 - Fitting offset from Lead End of Sheath\"\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003eType CM Fig. 1 - Fitting Flush with Lead End of Sheath\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eType CM Fig. 2 - Fitting offset from Lead End of Sheath\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ctable style=\"width: 101.875%;\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 100%;\"\u003e\n\u003cp\u003e\u003cem\u003eA single threaded pipe fitting is attached to the end of a cartridge heater to allow for installation into a threaded hole. This mounting option, available with many terminations, can also be offset from the lead end of the sheath. This option is useful when the lead wires need to be kept away from the heated area. Brass fittings are silver brazed and stainless steel fittings are heli-arc welded. Available with the potting seals listed in the table.\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-23 for Standard and Custom Features, as well as Ordering Information.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTo reference Standard (Stock \u0026amp; Non-Stock) Order Listings - Select \u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_US_Measures.pdf?v=1640092972\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List - US Measures and Values\" style=\"color: #ff2a00;\"\u003eUS Measures\u003c\/a\u003e\u003c\/span\u003e or\u003cspan\u003e \u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_Metric_Measures.pdf?v=1640092972%20\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List- Metric Measures \u0026amp; Values\" style=\"color: #ff2a00;\"\u003eMetric Measures\u003c\/a\u003e\u003c\/span\u003e.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ctable width=\"100%\" data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cp\u003e\u003cspan\u003e\u003cstrong\u003e\u003cem\u003eCMA\/CMN:\u003c\/em\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cem\u003e Low temperature epoxy potting — 266°F (130°C), UL rated to 194°F (90°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCMB\/CMP:\u003c\/strong\u003e Hi-temp cement potting with silicone varnish — 1000°F (538°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eFiberglass leads internally connected, rated 482°F (250°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCMC\/CMQ:\u003c\/strong\u003e Silicone rubber potting — 450°F (232°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eSilicone rubber leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCMD\/CMR:\u003c\/strong\u003e High temperature epoxy potting — 450°F (232°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCMV:\u003c\/strong\u003e Brass Fitting\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCMW:\u003c\/strong\u003e Stainless Steel Fitting\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eA minimum of 1\/4\" cold section below the bushing is required.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eStandard 10\" (254 mm) leads. Specify longer leads.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eSpecify offset dimension \"E\" when ordering.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eA termination must be specified separately.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCMB\u003c\/strong\u003e \u0026amp; \u003cstrong\u003eCMP\u003c\/strong\u003e are available through the Hi-Density Cartridge Heater Terminator Program for 2nd or 3rd Day Shipping.\u003c\/em\u003e\u003c\/p\u003e\n\u003cdiv class=\"scrollTable\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\"\u003e\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003cthead data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth colspan=\"5\" data-mce-fragment=\"1\"\u003eStandard NPT Bushing Dimensions\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth colspan=\"5\" data-mce-fragment=\"1\"\u003e(Fig. 1 \u0026amp; Fig. 2)\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth data-mce-fragment=\"1\"\u003eHeater Diameter\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003eNPT\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003e \u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003e \u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003e \u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth data-mce-fragment=\"1\"\u003e(in)\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003eSize\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003e“A”\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003e“B”\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003e“C”\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1\/4\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1⁄8-27\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3\/16\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e7\/16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e3\/8\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1⁄4-18\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1\/2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3\/16\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e9\/16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1\/2\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3⁄8-18\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e9\/16\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e11\/16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5\/8\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1⁄2-14\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e5\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e7\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e3\/4\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3⁄4-14\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1-1\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7\/8\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1-111⁄2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1-3\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1-111⁄2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1-3\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1-1\/4\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e11⁄4-111⁄2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e7\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e5\/16\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1-3\/4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003cthead data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth colspan=\"3\" data-mce-fragment=\"1\"\u003eType Codes for Single Threaded Fittings\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth data-mce-fragment=\"1\"\u003e \u003c\/th\u003e\n\u003cth colspan=\"2\" data-mce-fragment=\"1\"\u003eFitting Material\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth data-mce-fragment=\"1\"\u003ePotting Seal Type\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003eBrass\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003eStainless Steel\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong\u003eLow Temp Epoxy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMA\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMN\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong\u003eHi-Temp Cement\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMB\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMP\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong\u003eSilicone Rubber\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMC\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMQ\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong\u003eHi-Temp Epoxy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMD\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMR\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\n\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/em\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eNote:\u003c\/strong\u003e\u003cspan data-mce-fragment=\"1\"\u003e \u003c\/span\u003eFitting can be offset from end of sheath. See Figure 2.\u003c\/em\u003e\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003c\/em\u003e\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003eType CN: Double Threaded Fitting\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e \u003cimg style=\"display: block; margin-left: auto; margin-right: auto;\" src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/C029_CNA_Dim.jpg?Medium\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/C029_CNA_Dim.jpg?Medium\"\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003e\u003cem\u003ePotted end seals help to protect the heater from moisture or contamination from plastic material, cleaning solvents, or oils. The bushing cavity can be sealed with various materials such as:\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCNA\/CNN:\u003c\/strong\u003e Low temperature epoxy potting — 266°F (130°C), UL rated to 194°F (90°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCNB\/CNP:\u003c\/strong\u003e Hi-temp cement potting w\/ silicone varnish — 1000°F (538°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eFiberglass leads internally connected, rated 482°F (250°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCNC\/CNQ:\u003c\/strong\u003e Silicone rubber potting — 450°F (232°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eSilicone rubber leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCND\/CNR:\u003c\/strong\u003e High temperature epoxy potting — 450°F (232°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eA minimum of 1\/4\" cold section below the bushing is required.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eStandard 10\" (254 mm) leads. Specify longer leads.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eA termination must be specified separately\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-23 for Standard and Custom Features, as well as Ordering Information.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTo reference Standard (Stock \u0026amp; Non-Stock) Order Listings - Select \u003cspan style=\"color: #ff2a00;\"\u003e\u003ca style=\"color: #ff2a00;\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List - US Measures and Values\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_US_Measures.pdf?v=1640092972\"\u003eUS Measures\u003c\/a\u003e\u003c\/span\u003e or\u003cspan\u003e \u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca style=\"color: #ff2a00;\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List- Metric Measures \u0026amp; Values\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_Metric_Measures.pdf?v=1640092972%20\"\u003eMetric Measures\u003c\/a\u003e\u003c\/span\u003e.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cdiv class=\"scrollTable\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth colspan=\"5\"\u003eStandard NPT Bushing Dimensions\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHeater Diameter\u003c\/th\u003e\n\u003cth\u003eNPT\u003c\/th\u003e\n\u003cth\u003e \u003c\/th\u003e\n\u003cth\u003e \u003c\/th\u003e\n\u003cth\u003e \u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003e(in)\u003c\/th\u003e\n\u003cth\u003eSize\u003c\/th\u003e\n\u003cth\u003e“A”\u003c\/th\u003e\n\u003cth\u003e“B”\u003c\/th\u003e\n\u003cth\u003e“C”\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e1\/4\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1⁄8-27\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e7\/16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e3\/8\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1⁄4-18\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1\/2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e9\/16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e1\/2\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3⁄8-18\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e9\/16\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e11\/16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e5\/8\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1⁄2-14\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e5\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e5\/16\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e7\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e3\/4\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3⁄4-14\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1-1\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e7\/8\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1-111⁄2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1-3\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e1\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1-111⁄2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1-3\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e1-1\/4\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e11⁄4-111⁄2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e7\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1\/2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1-3\/4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth colspan=\"3\"\u003eType Codes for Double Threaded Fittings\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003e \u003c\/th\u003e\n\u003cth colspan=\"2\"\u003eFitting Material\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePotting Seal Type\u003c\/th\u003e\n\u003cth\u003eBrass\u003c\/th\u003e\n\u003cth\u003eStainless Steel\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003eLow Temp Epoxy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNA\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNN\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003eHi-Temp Cement\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNB\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNP\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003eSilicone Rubber\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNC\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNQ\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003eHi-Temp Epoxy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCND\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNR\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003e\u003cbr\u003e\u003c\/h4\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003eType TH: Top Hat Screw Plug\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e \u003cimg style=\"display: block; margin-left: auto; margin-right: auto;\" src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/TopHatSide_TH_Dim.jpg?Medium\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/TopHatSide_TH_Dim.jpg?Medium\"\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003e\u003cstrong\u003eLow temperature epoxy potting — 266°F (130°C), UL rated to 194°F (90°C)\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem\u003e\u003cstrong\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem\u003e\u003cstrong\u003eStandard 10\" (254 mm) leads. Specify longer leads.\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-23 for Standard and Custom Features, as well as Ordering Information.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTo reference Standard (Stock \u0026amp; Non-Stock) Order Listings - Select \u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_US_Measures.pdf?v=1640092972\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List - US Measures and Values\" style=\"color: #ff2a00;\"\u003eUS Measures\u003c\/a\u003e\u003c\/span\u003e or\u003cspan\u003e \u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_Metric_Measures.pdf?v=1640092972%20\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List- Metric Measures \u0026amp; Values\" style=\"color: #ff2a00;\"\u003eMetric Measures\u003c\/a\u003e\u003c\/span\u003e.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cem\u003e\u003c\/em\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cem\u003eConstruction Styles\u003c\/em\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003eType BF: Bulkhead Fitting\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cimg style=\"display: block; margin-left: auto; margin-right: auto;\" alt=\"\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC026.jpg\" src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC026.jpg?Small\" width=\"252\" height=\"186\"\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003e\u003cspan\u003e\u003cem\u003eA 5\/8-18 UNF fitting is attached to the end of the cartridge heater to allow for mounting the heater to the wall of a tank or enclosure. Brass fittings are silver brazed and stainless steel fittings are heli-arc welded. Includes a copper washer and jam nut. The lead wires are internally connected. Available with the potting seals listed in the table.\u003c\/em\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003ePotted end seals help to protect the heater from moisture or contamination from plastic material, cleaning solvents, or oils. The fitting cavity can be sealed with various materials such as:\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eBFA\/BFJ Low temperature epoxy potting\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— 266°F (130°C), UL rated to 194°F (90°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eBFB\/BFK Silicone rubber potting\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— 450°F (232°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eSilicone rubber leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eBFC\/BFL High temperature epoxy potting\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— 450°F (232°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eA minimum of 1\/4\" cold section below the bushing is required.\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eStandard 10\" (254 mm) leads. Specify longer leads.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-23 for Standard and Custom Features, as well as Ordering Information.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTo reference Standard (Stock \u0026amp; Non-Stock) Order Listings - Select \u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_US_Measures.pdf?v=1640092972\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List - US Measures and Values\" style=\"color: #ff2a00;\"\u003eUS Measures\u003c\/a\u003e\u003c\/span\u003e or\u003cspan\u003e \u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_Metric_Measures.pdf?v=1640092972%20\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List- Metric Measures \u0026amp; Values\" style=\"color: #ff2a00;\"\u003eMetric Measures\u003c\/a\u003e\u003c\/span\u003e.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ctable data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003e\n\u003cthead data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth colspan=\"3\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eType Codes for Bulkhead Fittings\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003e \u003c\/th\u003e\n\u003cth colspan=\"2\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eFitting Material\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003ePotting Seal Type\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBrass\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eStainless Steel\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eLow Temp Epoxy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBFA\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBFJ\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSilicone Rubber\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBFB\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBFK\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHi-Temp Epoxy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBFC\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBFL\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\"\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTypical Applications\u003c\/strong\u003e\u003c\/em\u003e\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePlastic Extruders\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHot Runner Molds\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHot Stamping\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eMedical Equipment\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackaging Equipment\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eMolds\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eAerospace\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSealing Bags\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSemiconductor\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePlastic Molding\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eShoe Machinery\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFood Processing\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHeating Gases and Liquids\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eGlue Guns\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eLaminating Presses\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePlatens\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eScientific Equipment\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFood Service Equipment\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","published_at":"2021-12-06T13:50:04-05:00","created_at":"2021-12-03T11:01:43-05:00","vendor":"Tempco","type":"Electronics","tags":["Electronics","Food \u0026 Beverage","Heaters","Manufacturing","Medical \u0026 Pharmaceutical Production","Plastic Fabrication","Process Heaet","Replacement Parts","Tempco"],"price":0,"price_min":0,"price_max":0,"available":true,"price_varies":false,"compare_at_price":null,"compare_at_price_min":0,"compare_at_price_max":0,"compare_at_price_varies":false,"variants":[{"id":42139237777627,"title":"Default Title","option1":"Default Title","option2":null,"option3":null,"sku":"HDL00001","requires_shipping":true,"taxable":false,"featured_image":null,"available":true,"name":"Tempco Hi-Density Immersion Cartridge Heaters","public_title":null,"options":["Default Title"],"price":0,"weight":2268,"compare_at_price":null,"inventory_management":null,"barcode":"","requires_selling_plan":false,"selling_plan_allocations":[]}],"images":["\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters.png?v=1638547305","\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters-1.png?v=1638547305","\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters-2.png?v=1638815934","\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters-3.png?v=1638815934"],"featured_image":"\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters.png?v=1638547305","options":["Title"],"media":[{"alt":null,"id":28792873451739,"position":1,"preview_image":{"aspect_ratio":1.979,"height":282,"width":558,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters.png?v=1638547305"},"aspect_ratio":1.979,"height":282,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters.png?v=1638547305","width":558},{"alt":null,"id":28792873484507,"position":2,"preview_image":{"aspect_ratio":0.846,"height":823,"width":696,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters-1.png?v=1638547305"},"aspect_ratio":0.846,"height":823,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters-1.png?v=1638547305","width":696},{"alt":null,"id":28807913210075,"position":3,"preview_image":{"aspect_ratio":0.842,"height":828,"width":697,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters-2.png?v=1638815934"},"aspect_ratio":0.842,"height":828,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters-2.png?v=1638815934","width":697},{"alt":null,"id":28807913242843,"position":4,"preview_image":{"aspect_ratio":0.832,"height":834,"width":694,"src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters-3.png?v=1638815934"},"aspect_ratio":0.832,"height":834,"media_type":"image","src":"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/products\/TempcoImmersionCartridgeHeaters-3.png?v=1638815934","width":694}],"requires_selling_plan":false,"selling_plan_groups":[],"content":"\u003cp data-mce-fragment=\"1\"\u003eTempco immersion cartridge heaters \u003cspan data-mce-fragment=\"1\"\u003eare designed for heating water and other liquids. The high watt density capabilities of this heater permit greater heat dissipation in given area than would tubular immersion heaters.  However, it is important to note that allowable watt density depends on the material being heated.  For water heating, watt densities of several hundred watts per square inch are possible; oil heating may be limited to 5 to 20 watts per square inch.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSpecifications:\u003c\/strong\u003e\u003c\/h3\u003e\n\u003ch4\u003e\u003cem\u003eDesign Features\u003c\/em\u003e\u003c\/h4\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cem\u003ePassivated Incoloy Sheath\u003c\/em\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cem\u003e10\" long Teflon® Insulated lead wires\u003c\/em\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cem\u003eBrass Fitting\u003c\/em\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cem\u003eEpoxy Seal at Lead End, 266°F (130°C) Standard, 194°F (90°C) UL Rating\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cem\u003eTermination Location\u003c\/em\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003ch4\u003eSingle-Ended Straight Termination\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003e \u003cimg src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC091.jpg?Small\" alt=\"\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC091.jpg\" width=\"223\" height=\"164\" style=\"display: block; margin-left: auto; margin-right: auto;\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC091.jpg?Small\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eThe Electrical Termination is located at one end of the heater and exits straight out from the heater.\u003c\/em\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003c\/h3\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003eElectrical Terminations\u003c\/em\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003eType F: Internally Connected Flexible Leads\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cimg height=\"164\" width=\"223\" alt=\"\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC002.jpg\" src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC002.jpg?Small\" style=\"display: block; margin-left: auto; margin-right: auto;\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC002.jpg?Small\"\u003e \u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003e\u003cem\u003eThe fiberglass lead wires are internally connected to the terminal pins. This lead termination provides flexibility, permitting the lead wires to be sharply bent as they exit the heater.\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eMinimum 3\/8\" up to 1\" unheated section at the lead end is required.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eStandard lead wire temperature rating for HDC \u0026amp; HDM: 842°F (450°C).\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eStandard lead wire temperature rating for LDC: 482°F (250°C).\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eStandard 10\" (254 mm) leads. Specify longer leads.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eFor HDC \u0026amp; HDM heaters, leads longer than 60\" require a splice.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-23 for Standard and Custom Features, as well as Ordering Information.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTo reference Standard (Stock \u0026amp; Non-Stock) Order Listings - Select \u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_US_Measures.pdf?v=1640092972\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List - US Measures and Values\" style=\"color: #ff2a00;\"\u003eUS Measures\u003c\/a\u003e\u003c\/span\u003e or\u003cspan\u003e \u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_Metric_Measures.pdf?v=1640092972%20\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List- Metric Measures \u0026amp; Values\" style=\"color: #ff2a00;\"\u003eMetric Measures\u003c\/a\u003e\u003c\/span\u003e.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/em\u003e\u003c\/h3\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTermination Options\u003c\/strong\u003e\u003c\/em\u003e\u003c\/h3\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003eType TL: Teflon® Leads\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eMaximum temperature rating: 200°C (392°F)\u003c\/em\u003e\u003cem\u003e \u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-23 for Standard and Custom Features, as well as Ordering Information.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTo reference Standard (Stock \u0026amp; Non-Stock) Order Listings - Select \u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_US_Measures.pdf?v=1640092972\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List - US Measures and Values\" style=\"color: #ff2a00;\"\u003eUS Measures\u003c\/a\u003e\u003c\/span\u003e or\u003cspan\u003e \u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_Metric_Measures.pdf?v=1640092972%20\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List- Metric Measures \u0026amp; Values\" style=\"color: #ff2a00;\"\u003eMetric Measures\u003c\/a\u003e\u003c\/span\u003e.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/em\u003e\u003c\/h3\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSheath Options\u003c\/strong\u003e\u003c\/em\u003e\u003c\/h3\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003eType CM: Single Threaded Fitting\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e        \u003cimg height=\"146\" width=\"253\" alt=\"Type CM Fig. 1 - Fitting Flush with Lead End of Sheath\" src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/C030_CMA_Fig1_Dim.jpg?Medium\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/C030_CMA_Fig1_Dim.jpg?Medium\"\u003e\n\u003c\/td\u003e\n\u003ctd\u003e\u003cimg height=\"146\" width=\"252\" src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/C030b_CMV_Fig2_Dim.jpg?Medium\" alt=\"Type CM Fig. 2 - Fitting offset from Lead End of Sheath\"\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003eType CM Fig. 1 - Fitting Flush with Lead End of Sheath\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eType CM Fig. 2 - Fitting offset from Lead End of Sheath\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ctable style=\"width: 101.875%;\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 100%;\"\u003e\n\u003cp\u003e\u003cem\u003eA single threaded pipe fitting is attached to the end of a cartridge heater to allow for installation into a threaded hole. This mounting option, available with many terminations, can also be offset from the lead end of the sheath. This option is useful when the lead wires need to be kept away from the heated area. Brass fittings are silver brazed and stainless steel fittings are heli-arc welded. Available with the potting seals listed in the table.\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-23 for Standard and Custom Features, as well as Ordering Information.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTo reference Standard (Stock \u0026amp; Non-Stock) Order Listings - Select \u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_US_Measures.pdf?v=1640092972\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List - US Measures and Values\" style=\"color: #ff2a00;\"\u003eUS Measures\u003c\/a\u003e\u003c\/span\u003e or\u003cspan\u003e \u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_Metric_Measures.pdf?v=1640092972%20\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List- Metric Measures \u0026amp; Values\" style=\"color: #ff2a00;\"\u003eMetric Measures\u003c\/a\u003e\u003c\/span\u003e.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ctable width=\"100%\" data-mce-fragment=\"1\"\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd data-mce-fragment=\"1\"\u003e\n\u003cp\u003e\u003cspan\u003e\u003cstrong\u003e\u003cem\u003eCMA\/CMN:\u003c\/em\u003e\u003c\/strong\u003e\u003c\/span\u003e\u003cem\u003e Low temperature epoxy potting — 266°F (130°C), UL rated to 194°F (90°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCMB\/CMP:\u003c\/strong\u003e Hi-temp cement potting with silicone varnish — 1000°F (538°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eFiberglass leads internally connected, rated 482°F (250°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCMC\/CMQ:\u003c\/strong\u003e Silicone rubber potting — 450°F (232°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eSilicone rubber leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCMD\/CMR:\u003c\/strong\u003e High temperature epoxy potting — 450°F (232°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCMV:\u003c\/strong\u003e Brass Fitting\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCMW:\u003c\/strong\u003e Stainless Steel Fitting\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eA minimum of 1\/4\" cold section below the bushing is required.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eStandard 10\" (254 mm) leads. Specify longer leads.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eSpecify offset dimension \"E\" when ordering.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eA termination must be specified separately.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCMB\u003c\/strong\u003e \u0026amp; \u003cstrong\u003eCMP\u003c\/strong\u003e are available through the Hi-Density Cartridge Heater Terminator Program for 2nd or 3rd Day Shipping.\u003c\/em\u003e\u003c\/p\u003e\n\u003cdiv class=\"scrollTable\"\u003e\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\"\u003e\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003cthead data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth colspan=\"5\" data-mce-fragment=\"1\"\u003eStandard NPT Bushing Dimensions\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth colspan=\"5\" data-mce-fragment=\"1\"\u003e(Fig. 1 \u0026amp; Fig. 2)\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth data-mce-fragment=\"1\"\u003eHeater Diameter\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003eNPT\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003e \u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003e \u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003e \u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth data-mce-fragment=\"1\"\u003e(in)\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003eSize\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003e“A”\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003e“B”\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003e“C”\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1\/4\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1⁄8-27\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3\/16\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e7\/16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e3\/8\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1⁄4-18\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1\/2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3\/16\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e9\/16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1\/2\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3⁄8-18\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e9\/16\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e11\/16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e5\/8\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1⁄2-14\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e5\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e7\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e3\/4\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3⁄4-14\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1-1\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e7\/8\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1-111⁄2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1-3\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1-111⁄2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e3\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1-3\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e1-1\/4\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e11⁄4-111⁄2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e7\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e5\/16\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e1-3\/4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\n\u003ctable data-mce-fragment=\"1\"\u003e\n\u003cthead data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth colspan=\"3\" data-mce-fragment=\"1\"\u003eType Codes for Single Threaded Fittings\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth data-mce-fragment=\"1\"\u003e \u003c\/th\u003e\n\u003cth colspan=\"2\" data-mce-fragment=\"1\"\u003eFitting Material\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth data-mce-fragment=\"1\"\u003ePotting Seal Type\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003eBrass\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\"\u003eStainless Steel\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong\u003eLow Temp Epoxy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMA\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMN\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong\u003eHi-Temp Cement\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMB\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMP\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong\u003eSilicone Rubber\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMC\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMQ\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003e\u003cstrong\u003eHi-Temp Epoxy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMD\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\"\u003eCMR\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003e\u003c\/span\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\n\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003c\/strong\u003e\u003c\/em\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eNote:\u003c\/strong\u003e\u003cspan data-mce-fragment=\"1\"\u003e \u003c\/span\u003eFitting can be offset from end of sheath. See Figure 2.\u003c\/em\u003e\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003c\/em\u003e\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\" data-mce-fragment=\"1\"\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003eType CN: Double Threaded Fitting\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e \u003cimg style=\"display: block; margin-left: auto; margin-right: auto;\" src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/C029_CNA_Dim.jpg?Medium\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/C029_CNA_Dim.jpg?Medium\"\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003e\u003cem\u003ePotted end seals help to protect the heater from moisture or contamination from plastic material, cleaning solvents, or oils. The bushing cavity can be sealed with various materials such as:\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCNA\/CNN:\u003c\/strong\u003e Low temperature epoxy potting — 266°F (130°C), UL rated to 194°F (90°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCNB\/CNP:\u003c\/strong\u003e Hi-temp cement potting w\/ silicone varnish — 1000°F (538°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eFiberglass leads internally connected, rated 482°F (250°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCNC\/CNQ:\u003c\/strong\u003e Silicone rubber potting — 450°F (232°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eSilicone rubber leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eCND\/CNR:\u003c\/strong\u003e High temperature epoxy potting — 450°F (232°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eA minimum of 1\/4\" cold section below the bushing is required.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eStandard 10\" (254 mm) leads. Specify longer leads.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eA termination must be specified separately\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-23 for Standard and Custom Features, as well as Ordering Information.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTo reference Standard (Stock \u0026amp; Non-Stock) Order Listings - Select \u003cspan style=\"color: #ff2a00;\"\u003e\u003ca style=\"color: #ff2a00;\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List - US Measures and Values\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_US_Measures.pdf?v=1640092972\"\u003eUS Measures\u003c\/a\u003e\u003c\/span\u003e or\u003cspan\u003e \u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca style=\"color: #ff2a00;\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List- Metric Measures \u0026amp; Values\" href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_Metric_Measures.pdf?v=1640092972%20\"\u003eMetric Measures\u003c\/a\u003e\u003c\/span\u003e.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cdiv class=\"scrollTable\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth colspan=\"5\"\u003eStandard NPT Bushing Dimensions\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eHeater Diameter\u003c\/th\u003e\n\u003cth\u003eNPT\u003c\/th\u003e\n\u003cth\u003e \u003c\/th\u003e\n\u003cth\u003e \u003c\/th\u003e\n\u003cth\u003e \u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003e(in)\u003c\/th\u003e\n\u003cth\u003eSize\u003c\/th\u003e\n\u003cth\u003e“A”\u003c\/th\u003e\n\u003cth\u003e“B”\u003c\/th\u003e\n\u003cth\u003e“C”\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e1\/4\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1⁄8-27\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e7\/16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e3\/8\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1⁄4-18\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1\/2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e9\/16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e1\/2\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3⁄8-18\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e9\/16\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e11\/16\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e5\/8\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1⁄2-14\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e5\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e5\/16\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e7\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e3\/4\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3⁄4-14\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1-1\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e7\/8\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1-111⁄2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1-3\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e1\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1-111⁄2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/4\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e3\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1-3\/8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003e1-1\/4\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e11⁄4-111⁄2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e7\/8\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1\/2\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003e1-3\/4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth colspan=\"3\"\u003eType Codes for Double Threaded Fittings\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003e \u003c\/th\u003e\n\u003cth colspan=\"2\"\u003eFitting Material\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePotting Seal Type\u003c\/th\u003e\n\u003cth\u003eBrass\u003c\/th\u003e\n\u003cth\u003eStainless Steel\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003eLow Temp Epoxy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNA\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNN\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003eHi-Temp Cement\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNB\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNP\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003eSilicone Rubber\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNC\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNQ\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"text-align: center;\"\u003e\u003cstrong\u003eHi-Temp Epoxy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCND\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\"\u003eCNR\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003e\u003cbr\u003e\u003c\/h4\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003eType TH: Top Hat Screw Plug\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e \u003cimg style=\"display: block; margin-left: auto; margin-right: auto;\" src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/TopHatSide_TH_Dim.jpg?Medium\" data-mce-fragment=\"1\" data-mce-src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/TopHatSide_TH_Dim.jpg?Medium\"\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003e\u003cstrong\u003eLow temperature epoxy potting — 266°F (130°C), UL rated to 194°F (90°C)\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem\u003e\u003cstrong\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem\u003e\u003cstrong\u003eStandard 10\" (254 mm) leads. Specify longer leads.\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-23 for Standard and Custom Features, as well as Ordering Information.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTo reference Standard (Stock \u0026amp; Non-Stock) Order Listings - Select \u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_US_Measures.pdf?v=1640092972\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List - US Measures and Values\" style=\"color: #ff2a00;\"\u003eUS Measures\u003c\/a\u003e\u003c\/span\u003e or\u003cspan\u003e \u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_Metric_Measures.pdf?v=1640092972%20\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List- Metric Measures \u0026amp; Values\" style=\"color: #ff2a00;\"\u003eMetric Measures\u003c\/a\u003e\u003c\/span\u003e.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cem\u003e\u003c\/em\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003e\u003cem\u003eConstruction Styles\u003c\/em\u003e\u003c\/strong\u003e\u003c\/h3\u003e\n\u003ch4 data-mce-fragment=\"1\"\u003eType BF: Bulkhead Fitting\u003c\/h4\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cimg style=\"display: block; margin-left: auto; margin-right: auto;\" alt=\"\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC026.jpg\" src=\"https:\/\/www.tempco.com\/Tempco\/Data-Assets\/02-Cartridge-Images\/WebC026.jpg?Small\" width=\"252\" height=\"186\"\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003e\u003cspan\u003e\u003cem\u003eA 5\/8-18 UNF fitting is attached to the end of the cartridge heater to allow for mounting the heater to the wall of a tank or enclosure. Brass fittings are silver brazed and stainless steel fittings are heli-arc welded. Includes a copper washer and jam nut. The lead wires are internally connected. Available with the potting seals listed in the table.\u003c\/em\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003ePotted end seals help to protect the heater from moisture or contamination from plastic material, cleaning solvents, or oils. The fitting cavity can be sealed with various materials such as:\u003c\/p\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eBFA\/BFJ Low temperature epoxy potting\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— 266°F (130°C), UL rated to 194°F (90°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eBFB\/BFK Silicone rubber potting\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— 450°F (232°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eSilicone rubber leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eBFC\/BFL High temperature epoxy potting\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003e— 450°F (232°C)\u003c\/em\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem\u003eTeflon® leads internally connected, rated 392°F (200°C).\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cem\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eA minimum of 1\/4\" cold section below the bushing is required.\u003c\/em\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eStandard 10\" (254 mm) leads. Specify longer leads.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-23 for Standard and Custom Features, as well as Ordering Information.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem data-mce-fragment=\"1\"\u003eSee reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e\u003cem\u003eTo reference Standard (Stock \u0026amp; Non-Stock) Order Listings - Select \u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_US_Measures.pdf?v=1640092972\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List - US Measures and Values\" style=\"color: #ff2a00;\"\u003eUS Measures\u003c\/a\u003e\u003c\/span\u003e or\u003cspan\u003e \u003c\/span\u003e\u003cspan style=\"color: #ff2a00;\"\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0249\/4467\/2845\/files\/Immersion_Cartridge_Heater_Order_List_-_Metric_Measures.pdf?v=1640092972%20\" title=\"Tempco Hi-Density Immersion Cartridge Heater Order List- Metric Measures \u0026amp; Values\" style=\"color: #ff2a00;\"\u003eMetric Measures\u003c\/a\u003e\u003c\/span\u003e.\u003c\/em\u003e\u003c\/strong\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ctable data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003e\n\u003cthead data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth colspan=\"3\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eType Codes for Bulkhead Fittings\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003e \u003c\/th\u003e\n\u003cth colspan=\"2\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eFitting Material\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003cth data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003ePotting Seal Type\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBrass\u003c\/th\u003e\n\u003cth data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eStainless Steel\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody data-mce-fragment=\"1\"\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eLow Temp Epoxy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBFA\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBFJ\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSilicone Rubber\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBFB\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBFK\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr data-mce-fragment=\"1\"\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHi-Temp Epoxy\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBFC\u003c\/td\u003e\n\u003ctd style=\"text-align: center;\" data-mce-fragment=\"1\" data-mce-selected=\"1\"\u003eBFL\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"scrollTable\"\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eTypical Applications\u003c\/strong\u003e\u003c\/em\u003e\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePlastic Extruders\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHot Runner Molds\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHot Stamping\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eMedical Equipment\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePackaging Equipment\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eMolds\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eAerospace\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSealing Bags\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eSemiconductor\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePlastic Molding\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eShoe Machinery\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFood Processing\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eHeating Gases and Liquids\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eGlue Guns\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eLaminating Presses\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003ePlatens\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eScientific Equipment\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cem data-mce-fragment=\"1\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eFood Service Equipment\u003c\/strong\u003e\u003c\/em\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e"}

Tempco Hi-Density Immersion Cartridge Heaters

Product Description

Tempco immersion cartridge heaters are designed for heating water and other liquids. The high watt density capabilities of this heater permit greater heat dissipation in given area than would tubular immersion heaters.  However, it is important to note that allowable watt density depends on the material being heated.  For water heating, watt densities of several hundred watts per square inch are possible; oil heating may be limited to 5 to 20 watts per square inch.

Specifications:

Design Features

  • Passivated Incoloy Sheath
  • 10" long Teflon® Insulated lead wires
  • Brass Fitting
  • Epoxy Seal at Lead End, 266°F (130°C) Standard, 194°F (90°C) UL Rating

Termination Location

Single-Ended Straight Termination

 /Tempco/Data-Assets/02-Cartridge-Images/WebC091.jpg

The Electrical Termination is located at one end of the heater and exits straight out from the heater.

Electrical Terminations

Type F: Internally Connected Flexible Leads

/Tempco/Data-Assets/02-Cartridge-Images/WebC002.jpg 

The fiberglass lead wires are internally connected to the terminal pins. This lead termination provides flexibility, permitting the lead wires to be sharply bent as they exit the heater.

  • Minimum 3/8" up to 1" unheated section at the lead end is required.
  • Standard lead wire temperature rating for HDC & HDM: 842°F (450°C).
  • Standard lead wire temperature rating for LDC: 482°F (250°C).
  • Standard 10" (254 mm) leads. Specify longer leads.
  • For HDC & HDM heaters, leads longer than 60" require a splice.
  • See reference page 2-23 for Standard and Custom Features, as well as Ordering Information.
  • See reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.
  • See reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.
  • To reference Standard (Stock & Non-Stock) Order Listings - Select US Measures or Metric Measures.

Termination Options

Type TL: Teflon® Leads

  • Maximum temperature rating: 200°C (392°F) 
  • See reference page 2-23 for Standard and Custom Features, as well as Ordering Information.
  • See reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.
  • See reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.
  • To reference Standard (Stock & Non-Stock) Order Listings - Select US Measures or Metric Measures.

Sheath Options

Type CM: Single Threaded Fitting

        Type CM Fig. 1 - Fitting Flush with Lead End of Sheath Type CM Fig. 2 - Fitting offset from Lead End of Sheath
Type CM Fig. 1 - Fitting Flush with Lead End of Sheath Type CM Fig. 2 - Fitting offset from Lead End of Sheath

A single threaded pipe fitting is attached to the end of a cartridge heater to allow for installation into a threaded hole. This mounting option, available with many terminations, can also be offset from the lead end of the sheath. This option is useful when the lead wires need to be kept away from the heated area. Brass fittings are silver brazed and stainless steel fittings are heli-arc welded. Available with the potting seals listed in the table.

  • See reference page 2-23 for Standard and Custom Features, as well as Ordering Information.
  • See reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.
  • See reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.
  • To reference Standard (Stock & Non-Stock) Order Listings - Select US Measures or Metric Measures.

    CMA/CMN: Low temperature epoxy potting — 266°F (130°C), UL rated to 194°F (90°C)

    • Teflon® leads internally connected, rated 392°F (200°C).

    CMB/CMP: Hi-temp cement potting with silicone varnish — 1000°F (538°C)

    • Fiberglass leads internally connected, rated 482°F (250°C).

    CMC/CMQ: Silicone rubber potting — 450°F (232°C)

    • Silicone rubber leads internally connected, rated 392°F (200°C).

    CMD/CMR: High temperature epoxy potting — 450°F (232°C)

    • Teflon® leads internally connected, rated 392°F (200°C).

    CMV: Brass Fitting

    CMW: Stainless Steel Fitting

    • A minimum of 1/4" cold section below the bushing is required.
    • Standard 10" (254 mm) leads. Specify longer leads.
    • Specify offset dimension "E" when ordering.
    • A termination must be specified separately.

    CMB & CMP are available through the Hi-Density Cartridge Heater Terminator Program for 2nd or 3rd Day Shipping.

    Standard NPT Bushing Dimensions
    (Fig. 1 & Fig. 2)
    Heater Diameter NPT      
    (in) Size “A” “B” “C”
    1/4 1⁄8-27 3/8 3/16 7/16
    3/8 1⁄4-18 1/2 3/16 9/16
    1/2 3⁄8-18 9/16 1/4 11/16
    5/8 1⁄2-14 5/8 1/4 7/8
    3/4 3⁄4-14 3/4 1/4 1-1/8
    7/8 1-111⁄2 3/4 1/4 1-3/8
    1 1-111⁄2 3/4 1/4 1-3/8
    1-1/4 11⁄4-111⁄2 7/8 5/16 1-3/4
    Type Codes for Single Threaded Fittings
      Fitting Material
    Potting Seal Type Brass Stainless Steel
    Low Temp Epoxy CMA CMN
    Hi-Temp Cement CMB CMP
    Silicone Rubber CMC CMQ
    Hi-Temp Epoxy CMD CMR


    Note: Fitting can be offset from end of sheath. See Figure 2.

    Type CN: Double Threaded Fitting

     

    Potted end seals help to protect the heater from moisture or contamination from plastic material, cleaning solvents, or oils. The bushing cavity can be sealed with various materials such as:

    CNA/CNN: Low temperature epoxy potting — 266°F (130°C), UL rated to 194°F (90°C)

    • Teflon® leads internally connected, rated 392°F (200°C).

    CNB/CNP: Hi-temp cement potting w/ silicone varnish — 1000°F (538°C)

    • Fiberglass leads internally connected, rated 482°F (250°C).

    CNC/CNQ: Silicone rubber potting — 450°F (232°C)

    • Silicone rubber leads internally connected, rated 392°F (200°C).

    CND/CNR: High temperature epoxy potting — 450°F (232°C)

    • Teflon® leads internally connected, rated 392°F (200°C).
    • A minimum of 1/4" cold section below the bushing is required.
    • Standard 10" (254 mm) leads. Specify longer leads.
    • A termination must be specified separately
    • See reference page 2-23 for Standard and Custom Features, as well as Ordering Information.
    • See reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.
    • See reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.
    • To reference Standard (Stock & Non-Stock) Order Listings - Select US Measures or Metric Measures.
      Standard NPT Bushing Dimensions
      Heater Diameter NPT      
      (in) Size “A” “B” “C”
      1/4 1⁄8-27 3/8 1/4 7/16
      3/8 1⁄4-18 1/2 1/4 9/16
      1/2 3⁄8-18 9/16 1/4 11/16
      5/8 1⁄2-14 5/8 5/16 7/8
      3/4 3⁄4-14 3/4 3/8 1-1/8
      7/8 1-111⁄2 3/4 3/8 1-3/8
      1 1-111⁄2 3/4 3/8 1-3/8
      1-1/4 11⁄4-111⁄2 7/8 1/2 1-3/4

      Type Codes for Double Threaded Fittings
        Fitting Material
      Potting Seal Type Brass Stainless Steel
      Low Temp Epoxy CNA CNN
      Hi-Temp Cement CNB CNP
      Silicone Rubber CNC CNQ
      Hi-Temp Epoxy CND CNR


      Type TH: Top Hat Screw Plug

       
      • Low temperature epoxy potting — 266°F (130°C), UL rated to 194°F (90°C)
      • Teflon® leads internally connected, rated 392°F (200°C).
      • Standard 10" (254 mm) leads. Specify longer leads.
      • See reference page 2-23 for Standard and Custom Features, as well as Ordering Information.
      • See reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.
      • See reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.
      • To reference Standard (Stock & Non-Stock) Order Listings - Select US Measures or Metric Measures.

        Construction Styles

        Type BF: Bulkhead Fitting

        /Tempco/Data-Assets/02-Cartridge-Images/WebC026.jpg

        A 5/8-18 UNF fitting is attached to the end of the cartridge heater to allow for mounting the heater to the wall of a tank or enclosure. Brass fittings are silver brazed and stainless steel fittings are heli-arc welded. Includes a copper washer and jam nut. The lead wires are internally connected. Available with the potting seals listed in the table.

        Potted end seals help to protect the heater from moisture or contamination from plastic material, cleaning solvents, or oils. The fitting cavity can be sealed with various materials such as:

        BFA/BFJ Low temperature epoxy potting — 266°F (130°C), UL rated to 194°F (90°C)

        • Teflon® leads internally connected, rated 392°F (200°C).

        BFB/BFK Silicone rubber potting — 450°F (232°C)

        • Silicone rubber leads internally connected, rated 392°F (200°C).

        BFC/BFL High temperature epoxy potting — 450°F (232°C)

        • Teflon® leads internally connected, rated 392°F (200°C).

        Note: A minimum of 1/4" cold section below the bushing is required.

        • Standard 10" (254 mm) leads. Specify longer leads.
        • See reference page 2-23 for Standard and Custom Features, as well as Ordering Information.
        • See reference page 2-50 for Single Ended National Pipe Thread (NPT) Fitting - Termination Flush and Offset with End of Sheath.
        • See reference page 2-51 for Double Ended National Pipe Thread (NPT) Fitting - Top Hat and Bulk Head Fitting Termination.
        • To reference Standard (Stock & Non-Stock) Order Listings - Select US Measures or Metric Measures.
        Type Codes for Bulkhead Fittings
          Fitting Material
        Potting Seal Type Brass Stainless Steel
        Low Temp Epoxy BFA BFJ
        Silicone Rubber BFB BFK
        Hi-Temp Epoxy BFC BFL

         

        Typical Applications

        • Plastic Extruders
        • Hot Runner Molds
        • Hot Stamping
        • Medical Equipment
        • Packaging Equipment
        • Molds
        • Aerospace
        • Sealing Bags
        • Semiconductor
        • Plastic Molding
        • Shoe Machinery
        • Food Processing
        • Heating Gases and Liquids
        • Glue Guns
        • Laminating Presses
        • Platens
        • Scientific Equipment
        • Food Service Equipment
        Sku: HDL00001
        Vendor: Tempco
        Call for Product Support & Pricing
        Maximum quantity available reached.

        Related products